On this page

Rapid Prototyping for Robotics: Choosing 3D Printing, CNC or Sheet Metal

Choose a rapid prototyping process by the question the robot part must answer. 3D printing can suit complex geometry and quick fit iterations. CNC machining can suit a specified stock material and controlled mating features. Sheet metal can suit covers, folded brackets and panels. The choice belongs to the part, material and inspection requirement.

There is no required journey from a printed prototype to a machined part. A bent cover may stay sheet metal throughout development. A printed fixture may remain the accepted production aid. A bearing support may need its intended material and manufacturing route from the first loaded test.

Define what this prototype is allowed to prove

Write one sentence before requesting a quote: “This part will demonstrate connector access on assembly R-01 A” or “This part will support the specified load during test T-07.” State the configuration, required evidence and limits. Keep stiffness, thermal behaviour and service life as separate verification questions.

Prototype purposeEvidence to collectClaim that remains open
Appearance and accessPhotos, cable-routing observations and access measurementsLoad capacity and long-term material behaviour
Mating and assemblyCritical dimensions, assembly sequence and clearance checksPerformance outside the checked mating configuration
Loaded functionMaterial/process identity, instrumented response and defined acceptance criteriaUnexecuted life, environment and fault conditions
Manufacturing learningSupplier feedback, inspection results and assembly issuesRepeatability of another process or supplier

Give a prototype its own controlled identity when it differs from the intended product. Record the difference explicitly. The revision and configuration guide shows why a part revision alone cannot describe the complete test article.

Match the process to the functional features

ProcessUseful candidateQuestions for the supplierAcceptance evidence
3D printingComplex enclosure, routing aid or application-specific fixtureExact process and material grade, orientation, supports, post-processing and critical-feature capabilityAgreed dimensions and evidence appropriate to the proposed loading and environment
CNC machiningBearing carrier, mounting block or other stock-material partTool access, setups, internal corners, stock grade, surface finish and treatmentDrawing-based measurements of mating features, with material evidence where required
Sheet metalPanel, guard or folded support with uniform material thicknessBend geometry, feature-to-bend spacing, flat-pattern responsibility and inserted hardwareDimensions in the formed condition and checks of the assembled interfaces

Specify the additive process and material grade explicitly. Protolabs' process guide distinguishes several additive routes. Choose the route and grade that match the question, then agree how the finished part will be assessed. Check the conditions before applying a datasheet value or result to another process.

For CNC, examine the supplier's machining guidelines for the selected material and geometry. For folded parts, sheet metal guidelines distinguish features on one surface from dimensions across bends. These supplier-specific inputs help assess the drawing and quoted feature requirements.

Work a three-part robot example

Consider a fictional inspection robot with a cable cover, bearing support and bent battery tray. The team needs four prototype sets. No manufacturing or test results are claimed for these example parts.

The cable cover's first job is to confirm connector access. A printed cover is a candidate because the team expects to change its routing geometry. Mark it as an access prototype. Record any material difference from the intended cover and leave protective and environmental performance unverified.

The bearing support's fictional drawing requires two mounting centres at 40.00 ± 0.05 mm. That is the project's drawing requirement. A load of 60 N acting 0.05 m from the mounting plane creates a simple moment of 60 × 0.05 = 3 N·m. This load calculation identifies an input for analysis and testing. The team must assess the support and fasteners against it. A machined candidate should be quoted against the specified material, mating datums and inspection plan.

The battery tray is a folded part. Ask the fabricator to review hole positions, bend access and the installed envelope. Measure relevant features after forming. Use the intended fastening arrangement when checking fit, so the check represents the clamped assembly.

If the support carries an actuator, agree the mounting and load interface using the actuator sourcing brief. Assess the bracket's structural and alignment requirements alongside the supplier's motor rating.

Send a quote pack with an inspection decision

Include the CAD file and revision, drawing and revision, quantity, required date, intended purpose and material specification. Identify critical features, datum scheme, threads, finish, inserted hardware and any allowed departures. Ask the supplier to state which file governs when CAD and drawing disagree. Resolve that discrepancy before manufacture.

Choose inspection evidence at quotation, when it can be costed and scheduled. Protolabs' sheet metal quality guide distinguishes a conformity certificate from dimensional and first-article reports. The same distinction is useful when reviewing another supplier: a statement of conformity and a table of actual measured dimensions answer different questions.

A fictional quote offers four parts at £20 each, £140 setup and £20 freight, totalling £240 with the required inspection included. Another offers four at £55 and £20 freight, also £240, but excludes a £90 inspection charge. Its comparable total is £330. These are invented figures illustrating quote reconciliation. Keep real process, material and inspection scope equal before comparing totals, following the costed BOM method.

Accept the part against its purpose and configuration

At receipt, check identity and revision before dimensions or function. Record measured features, deviations and the decision about each deviation. For a loaded test, define instrumentation, setup, limits and acceptance criteria before execution. Retain the fixture and configuration details needed to interpret the result.

Arc's robotics product workflow links build references and compatibility evidence. An appropriate trial connects a prototype's drawing, declared differences and test result to the requirement being assessed. Confirm the actual manufacturing and purchasing handoffs separately. Use the EBOM-to-MBOM example when manufacturing steps, inserts or consumables need their own records.

Rapid prototyping questions

Can a printed part be used in a loaded robot prototype?

Yes, if the chosen process, material, geometry and evidence meet that prototype's defined purpose. Inspect and assess the relevant load and environment. Define acceptance criteria for the prototype's intended use.

Which process has the best tolerance?

Compare the exact feature, material, part size, setup and quoted capability. Ask how the supplier will measure that feature. Keep the conditions that matter to the mating assembly alongside the quoted number.

Is the shortest quoted manufacturing time always the fastest route?

Include design review, file corrections, transport, inspection and any planned rework. A quick part that cannot answer the intended question may add another iteration. Agree a useful acceptance pack and delivery milestone.

Move faster without compromising engineering rigour.

Bring a prototype drawing and its acceptance question to see how Arc connects it to the proposed build.