On this page

How to Source Robot Actuators, Gearboxes and Motors

Source a robot actuator by describing the required motion, loads and operating conditions before comparing suppliers. Record output torque and speed together, the duration of each load phase, mounting and thermal conditions, and the electrical and control interfaces. Then ask suppliers to show how the proposed part meets that brief.

A motor, a gearbox and an integrated actuator are different supply boundaries. A motor needs a compatible drive and mechanical connection. A gearbox needs an input drive and supported load interface. An integrated actuator may include several of those elements, with remaining responsibilities defined in its specification. Make those boundaries explicit before comparing cost or delivery.

Write a motion brief the supplier can evaluate

Give each axis an identifier and name the configuration it serves. State the output load at the shaft or joint, the speed range and movement profile. Include acceleration, holding periods, reversing, expected operating time and the required environmental conditions. Keep calculated loads, measured loads and assumptions in separate fields.

Brief fieldInformation to provideEvidence to request
Output motionTorque in N·m, speed in rpm, travel and time historyPermitted operating points and cycle limits
Mechanical installationMounting datum, envelope, shaft/flange, radial and axial loadsControlled drawing and bearing/load limits
Thermal conditionsAmbient temperature, cooling path, enclosure and mountingRating conditions, derating and thermal limits
Electrical supplyVoltage range, current limit and available driveMotor/drive pairing, current demand and braking requirements
Control and feedbackEncoder type, interface, command modes and fault responseInterface manual, connector pinout and supported firmware
Support and changeQuantity, required date, repair plan and expected service periodQuote, change-notification route and replacement policy

Request dimensions in the installed condition, including connector clearance and cable bend space. If a bracket is being designed, share the interface brief with that designer. The rapid prototyping guide helps define what an early bracket must demonstrate.

Compare continuous and peak torque under stated conditions

Put the rating's conditions beside its value. A peak torque needs a permitted duration and repetition rule. A continuous rating needs its speed and thermal conditions. Harmonic Drive's gear-unit table separates rated torque, repeated peak limits and momentary peak limits. Treat those as distinct supplier definitions.

For motors, maxon's motor-selection reference explains why the load cycle and heat-transfer conditions matter. It is a November 2014 reference, useful for the engineering method. Use a current part datasheet and supplier confirmation for the actual selection.

Check the complete motor speed-torque operating points within the proposed supply and drive limits. Include acceleration and reflected inertia where relevant. Review the gearbox's input speed, continuous and intermittent output limits, efficiency and load capacity. A rating for one component cannot establish the complete axis's performance.

Work a simple motor and gearbox example

The fictional AX-02 axis rotates an inspection fixture. Its approved preliminary brief asks for 6 N·m at 30 rpm during steady motion and 12 N·m for 0.5 seconds during acceleration. For this first calculation, assume a 20:1 gearbox and 80% efficiency at the relevant operating points. These values describe a teaching example, with no selected supplier or tested actuator.

Using the conversion described in maxon's April 2023 gear reference, motor speed is 20 × 30 = 600 rpm. Steady motor torque is 6 / (20 × 0.80) = 0.375 N·m. The corresponding load-related peak is 12 / (20 × 0.80) = 0.750 N·m. Add the required motor-side acceleration and other losses when refining the model.

Steady output power is approximately 6 × 2π × 30 / 60 = 18.85 W. At the assumed gearbox efficiency, mechanical input power is about 18.85 / 0.80 = 23.56 W. Electrical input will depend on motor and drive losses. Keep the efficiency assumption attached to the calculation and replace it with supplier evidence for the chosen operating points.

Example requirementCandidate evidence neededDecision before approval
6 N·m at 30 rpmMotor operating point and gearbox continuous capacityConfirm performance at the installed thermal conditions
12 N·m for 0.5 sPermitted intermittent motor/drive and gearbox envelopeConfirm cycle frequency, acceleration and recovery conditions
20:1 assumed ratioExact ratio, efficiency, input-speed limit and output-load dataUpdate calculations against the offered ordering code

The example screens the questions to ask. Complete the duty-cycle thermal assessment, structural/interface checks and acceptance plan before calling a candidate suitable. State any project margin rule with its authority, instead of adding an unexplained multiplier.

Check the integration boundary before ordering

For a motor-plus-gearbox purchase, establish who owns shaft coupling, alignment, support bearings, brake, encoder and drive selection. For an integrated actuator, request a delivered-content list and interface documents. Confirm the connector, supply, communications, calibration and firmware requirements from the actual offered configuration.

Review holding and power-loss behaviour as application requirements. Request evidence for the relevant condition before assigning a protective function to a brake or gearbox. Backdriving, backlash and stiffness are separate properties. Ask how each is specified and measured at the intended load.

Use the part-numbering guide to separate the internal axis assembly, manufacturer ordering code and supplier SKU. A changed encoder option or gearbox ratio may need a different selected item or configuration, even when the sales family name stays the same.

Turn the supplier reply into an approval pack

Keep the dated quote, exact ordering code, drawings, manuals, load calculations and outstanding questions together. Identify who accepts each technical question and who authorises the purchase. Record service, spare and change-notification assumptions. Reconcile delivery and cost with the costed BOM.

Arc's robotics product workflow links selected parts, revisions, drawings and source handoffs for review. An appropriate evaluation connects the AX-02 choice to its BOM and build configuration, then follows a proposed gearbox change through the affected records. Use the configuration matrix to preserve the accepted choice and its applicability. Confirm purchase execution in the system that owns orders.

Robot actuator sourcing questions

Can peak torque determine actuator size?

Use it with the complete motion cycle, speed and thermal requirements. Check the permitted peak duration and repetition rate, as well as the continuous operating points. Keep motor, drive and gearbox limits visible separately.

Does a higher gear ratio always improve the choice?

Evaluate its motor speed, losses, stiffness, backdriving and duty consequences. The selected ratio must fit the available motor and drive operating envelope and the gearbox's input-speed limits.

How should an actuator substitution be approved?

Compare the exact offered configuration with the accepted interface and performance brief. Trace mechanical, electrical, control and verification consequences. Record any additional evidence and the applicable builds before releasing the replacement.

Move faster without compromising engineering rigour.

Bring an actuator brief, drawing and supplier reply to review the affected BOM and build references in Arc.